Loader Operator - Bowmanville (Nights)

Votorantim Cimento

  • Bowmanville, ON
  • Permanent
  • Temps-plein
  • Il y a 1 mois
Job DescriptionThe Night Shift Front-End Loader Operator is responsible for a variety of daily tasks that support the efficient operation of the Ready-Mix plant. The Front-End Loader Operator is a generalist who is responsible for a range of duties including, but not limited to:
  • Running and monitoring (including boiler tests) the boiler system in cold months,
  • Forming and stripping of returned concrete blocks,
  • Yard housekeeping / snow removal
  • Receiving and inspection of aggregates,
  • A Plant Inspections,
  • In yard concrete testing,
  • Daily fuel dip/measurement,
  • Minor plant maintenance, grease and/or lube equipment as required
  • Maintaining the washout pit and drying bay
  • Operating the loader
  • Cleaning and shovelling under belts
Loader OperationThe loader is used to organize aggregate bins in the yard. When new loads of aggregate are delivered, the loader is used to form organized piles so that the bin capacity is effectively utilized. The loader is also used to retrieve aggregate from yard bins and load into the hopper to supply the plant conveyor. The loader is also used to remove sediment from the bottom of the washout station.Boiler OperationsIn the cold months, boilers are used to maintain critical temperatures of materials used in the concrete mix. It is the responsibility of the Loader/Yard Operator to operate and monitor the boiler during the months of cold temperatures.General MaintenanceThe Loader/Yard Operator duties include performing general maintenance of equipment that supports the plant operations. This includes lubrication points and minor repairs as necessary.General HousekeepingThe Loader/Yard Operator is responsible for such housekeeping tasks as shoveling, sweeping and snow removal.Block FormingExcess concrete is often unloaded from the mixers into concrete forms to make blocks used in constructing walls or barricades. These blocks are either sold or used by the Plant. The driver of the mixer unloads the remaining concrete from the mixer. The form is finished using a hand trowel. After 24 to 48 hours, the steel mold is released from the form by removing the pins holding the sides together and prying the mold away from the concrete using a pry-bar.Receiving and Inspection of aggregatesInspect ticket to ensure that material received matches material on delivery ticket and sign for it. Inspect material for contamination. Push material into pile.A InspectionsInspection of plant equipment, conveyor belts, aggregate gates, scales, air compressor, boiler, collecting hopper, Health, and Safety - housekeeping, guards in place, logbooks. Findings are reported on A Inspection forms.In Yard concrete testingAir, temperature, and slump testingDaily Fuel DipRemoval of tank fuel cap and insertion of dip stick to obtain fuel level. Report readings to plant managerReclaimers/Washout (use applicable per location)Reclaimer separates the slurry water and the sand & stone. The slurry water is pumped back to the plants to be reused in loads. The sand and stone is put back into the pile.Washout system, water is pumped from this ramp area into a holding tank. This water settles and the sediment goes to the bottom of the tank. The water is then pumped into a separate tank and this water is reused for the trucks to washout again. It is a cycle to contain the washout water.Loader Inspection / ServiceThe Loader/Yard Operator must also care for their vehicle by conducting daily inspections of hydraulic lines, tires, and cylinders. This requires a perimeter check of the vehicle, squatting and looking under the vehicle at these various components. The operator must also regularly (daily) grease components of the vehicle using a manual grease gun.Light Maintenance DutyThe Loader/Yard Operator may occasionally be required to assist maintenance technicians with service to their vehicles. This may require operating specific controls of the loader during trouble-shooting, and occasional use of hand-tools and power tools.QualificationsMust have a valid Ontario's Driver Licence;OSSGD or equivalent;Passing Grade on Mechanical Aptitude Test, Math Skills Test and Literacy Test;Prior experience operating mobile material handling equipment (the successful candidate must become certified to operate the Loader within a reasonable period of time following the awarding of the position).Testing RequiredPassing Grade on Mechanical Aptitude Test, Math Skills Test and Literacy Test#CBMHP

Votorantim Cimento